Command Section
RADIUS.CONF(5)            FreeBSD File Formats Manual           RADIUS.CONF(5)

     radius.conf - RADIUS client configuration file


     radius.conf contains the information necessary to configure the RADIUS
     client library.  It is parsed by rad_config(3).  The file contains one or
     more lines of text, each describing a single RADIUS server which will be
     used by the library.  Leading white space is ignored, as are empty lines
     and lines containing only comments.

     A RADIUS server is described by three to seven fields on a line:

           Service type
           Server host
           Shared secret
           Dead time
           Bind address

     The fields are separated by white space.  The `#' character at the
     beginning of a field begins a comment, which extends to the end of the
     line.  A field may be enclosed in double quotes, in which case it may
     contain white space and/or begin with the `#' character.  Within a quoted
     string, the double quote character can be represented by `\"', and the
     backslash can be represented by `\\'.  No other escape sequences are

     The first field gives the service type, either `auth' for RADIUS
     authentication or `acct' for RADIUS accounting.  If a single server
     provides both services, two lines are required in the file.  Earlier
     versions of this file did not include a service type.  For backward
     compatibility, if the first field is not `auth' or `acct' the library
     behaves as if `auth' were specified, and interprets the fields in the
     line as if they were fields two through five.

     The second field specifies the server host, either as a fully qualified
     domain name or as a dotted-quad IP address.  The host may optionally be
     followed by a `:' and a numeric port number, without intervening white
     space.  If the port specification is omitted, it defaults to the `radius'
     or `radacct' service in the /etc/services file for service types `auth'
     and `acct', respectively.  If no such entry is present, the standard
     ports 1812 and 1813 are used.

     The third field contains the shared secret, which should be known only to
     the client and server hosts.  It is an arbitrary string of characters,
     though it must be enclosed in double quotes if it contains white space.
     The shared secret may be any length, but the RADIUS protocol uses only
     the first 128 characters.  N.B., some popular RADIUS servers have bugs
     which prevent them from working properly with secrets longer than 16

     The fourth field contains a decimal integer specifying the timeout in
     seconds for receiving a valid reply from the server.  If this field is
     omitted, it defaults to 3 seconds.

     The fifth field contains a decimal integer specifying the maximum number
     of attempts that will be made to authenticate with the server before
     giving up.  If omitted, it defaults to 3 attempts.  Note, this is the
     total number of attempts and not the number of retries.

     The sixth field contains a decimal integer specifying a time interval in
     seconds when the server will not requested if it was inaccessible on the
     last try. 0 means ask always.

     The seventh field contains an IP address on multihomed host. All requests
     will be binded to this IP.

     Up to 10 RADIUS servers may be specified for each service type.  The
     servers are tried in round-robin fashion, until a valid response is
     received or the maximum number of tries has been reached for all servers.

     The standard location for this file is /etc/radius.conf.  But an
     alternate pathname may be specified in the call to rad_config(3).  Since
     the file contains sensitive information in the form of the shared
     secrets, it should not be readable except by root.


     # A simple entry using all the defaults:
     acct  OurLittleSecret

     # A server still using the obsolete RADIUS port, with increased
     # timeout and maximum tries:
     auth  "I can't see you"  5  4

     # As above but set dead time and bind address
     auth  "I can't see you"  5  4  60

     # A server specified by its IP address:
     auth  $X*#..38947ax-+=


     C. Rigney, et al, Remote Authentication Dial In User Service (RADIUS),
     RFC 2138.

     C. Rigney, RADIUS Accounting, RFC 2139.

     This documentation was written by John Polstra, and donated to the
     FreeBSD project by Juniper Networks, Inc.

FreeBSD 11.1-RELEASE-p4        October 30, 1999        FreeBSD 11.1-RELEASE-p4
Command Section