Command Section
GEOM_FOX(4)            FreeBSD Kernel Interfaces Manual            GEOM_FOX(4)

     geom_fox - GEOM based basic disk multipathing

     To compile this driver into the kernel, place the following line in your
     kernel configuration file:

           options GEOM_FOX

     Alternatively, to load the driver as a module at boot time, place the
     following line in loader.conf(5):


     This driver is obsolete.  Users are advised to use gmultipath(8) instead.

     The intent of the geom_fox framework is to provide basic multipathing
     support to access direct access devices.  Basic in the above sentence
     should be read as: geom_fox only provides path failover functionality,
     not load balancing over the available paths etc.  Using suitable hardware
     like SCSI or FibreChannel disks it is possible to have multiple
     (typically 2) host bus adapters access the same physical disk drive.

     Without a multipathing driver the FreeBSD kernel would probe the disks
     multiple times, resulting in the creation of multiple /dev entries for
     the same underlying physical device.  A unique label written in the GEOM
     label area allows geom_fox to detect multiple paths.  Using this
     information it creates a unique device.

     The geom_fox device is subsequently used by the FreeBSD kernel to access
     the disks.  Multiple physical access paths ensure that even in case of a
     path failure the FreeBSD kernel can continue to access the data.

     The geom_fox driver will disallow write operations to the underlying
     devices once the fox device has been opened for writing.

        geom_fox needs a label on the disk as follows in order to work

         "GEOM::FOX       <--unique--id-->"

         For the unique ID 16 bytes are available.  The ``GEOM::FOX'' is the
         magic to mark a geom_fox device.

         The actual labelling is accomplished by

         echo "GEOM::FOX       someid" | dd of=/dev/da2 conv=sync

         For FibreChannel devices it is suggested to use the Node World Wide
         Name (Node WWN) as this is guaranteed by the FibreChannel standard to
         be worldwide unique.  The use of the Port WWN not recommended as each
         port of a given device has a different WWN, thereby confusing things.

         The Node WWN can be obtained from a verbose boot as in for example

         isp1: Target 1 (Loop 0x1) Port ID 0xe8 (role Target) Arrived
          Port WWN 0x21000004cfc8aca2
          Node WWN 0x20000004cfc8aca2

         This Node WWN would then be used like so:

         echo "GEOM::FOX       20000004cfc8aca2" | dd of=/dev/da2 conv=sync

         For non-FibreChannel devices you could for example use the serial
         number of the device.  Regardless of what you use, make sure the
         label is unique.

         Once the labelling has been performed and assuming the geom_fox
         module is loaded the kernel will inform you that it has found a new
         geom_fox device with a message similar to

         Creating new fox (da2)
         fox lock 0xfffffc0000fdba20

        To check which physical devices match a given geom_fox device:

               # geom fox list
               Geom name:
               1. Name:
                  Mediasize: 73407865344 (68G)
                  Sectorsize: 512
                  Mode: r0w0e0
               1. Name: da2
                  Mediasize: 73407865856 (68G)
                  Sectorsize: 512
                  Mode: r0w0e0
               2. Name: da6
                  Mediasize: 73407865856 (68G)
                  Sectorsize: 512
                  Mode: r0w0e0

        To check the status of the geom_fox components:

         # geom fox status
            Name  Status  Components     N/A  da2

     GEOM(4), geom(8), gmultipath(8)

     The geom_fox driver was written by Poul-Henning Kamp <[email protected]>.
     This manual page was written by Wilko Bulte <[email protected]>.

     The geom_fox driver depends on the underlying hardware drivers to do the
     right thing in case of a path failure.  If for example a hardware driver
     continues to retry forever, geom_fox is not able to re-initiate the I/O
     to an alternative physical path.

     You have to be very sure to provide a unique label for each of the
     geom_fox devices.  Safety belts are not provided.  For FibreChannel
     devices it is suggested to use the Port WWN of the device.  The World
     Wide Name is guaranteed to be worldwide unique per the FibreChannel

     The geom_fox framework has only seen light testing.  There definitely
     might be dragons here.

     The name geom_fox is completely obscure.  Just remember that any sly fox
     has multiple exits from its hole.

     The examples provided are too FibreChannel-centric.

FreeBSD 11.1-RELEASE-p4       September 12, 2015       FreeBSD 11.1-RELEASE-p4
Command Section